<%NUMBERING1%>.<%NUMBERING2%>.<%NUMBERING3%> PRTG Manual: Install a Remote Probe

Remote probes can extend your monitoring with PRTG.

  • With remote probes, you can monitor different subnetworks that are separated from your PRTG on premises core server by a firewall, and you can keep an eye on remote locations. You can install one or more remote probes.
  • Remote probes are useful if you want to distribute monitoring load by taking it from the PRTG core server system and putting it on one or more remote probe systems.
  • You need a remote probe if you want to monitor your local network using a PRTG Hosted Monitor instance.

i_round_bluePRTG automatically updates remote probes but, in rare cases, you have to manually update remote probes. You receive a ToDo ticket in this case. Follow the steps below to manually update remote probes.

i_round_redIf you run PRTG in a cluster, see Cluster and Remote Probes Outside the LAN in this section.

i_square_cyanIf you have issues after the installation, see section Debugging Remote Probe Connection Issues.

i_square_cyanFor a partially automatic installation of a remote probe directly from the device tree in the PRTG web interface, see section Remote Probe Setup via Device Tools. For a quick installation guide, see the Paessler Website: How to install a PRTG remote probe in 4 steps.

Steps to Take

To install a remote probe with the Remote Probe Installer, follow these steps:

Step 1: Meet the Requirements

To install a remote probe on a computer, make sure that you meet the following requirements.

  • The target computer runs the operating system Windows 7 or later.
  • The target computer is accessible through remote procedure call (RPC). This is usually the case when your PRTG core server and the target computer are located in the same LAN segment. Otherwise, open Windows services.msc on the target computer and start the RPC service.
  • Programs are allowed to communicate through your Windows Firewall. Open the settings of your firewall and select Allow an app through firewall. Mark the check box for Remote Service Management, and the check box Public in the corresponding line.
  • Connections between remote probes and the PRTG core server require port 23560. Make sure that on your PRTG core server side, this port is not blocked by firewall rules, and, on the remote probe side, the Transmission Control Protocol (TCP) port 23560 is open for outgoing connections as well.
    i_square_cyanIf you need to set a different port (not recommended), see the Knowledge Base: How can I customize ports for core-probe connections used by PRTG?

i_round_blueYour PRTG on premises or PRTG Hosted Monitor installations already include a local probe or hosted probe on the PRTG core server. This is why you cannot additionally install a remote probe on your PRTG core server system.

i_square_cyanFor more information on the requirements for remote probes, see section System Requirements.

Step 2: Prepare the PRTG Core Server

i_podThis only applies to PRTG on premises installations, not to PRTG Hosted Monitor instances.

If you use PRTG Hosted Monitor, you can start with Step 3: Download the Remote Probe Installer from the PRTG Web Interface right away.

i_round_redBecause your remote probe needs to connect to your PRTG core server, PRTG needs to accept incoming remote probe connections. So, with PRTG on premises, first prepare your PRTG core server before you install the remote probe.

Edit the relevant settings in section Core & Probes. From the main menu in the PRTG web interface, select Setup | System Administration | Core & Probes to access the probe settings and go to the Probe Connection Settings.

Probe Connection Settings in System Administration

Probe Connection Settings in System Administration

Step 2.1: Probe Connection IPs

By default, a PRTG core server accepts connections from the Local Probe only (IP address 127.0.0.1). This setting is the most secure setting, but it does not allow any remote probes to connect to your PRTG core server.

To accept remote probes, select one of the following settings:

  • All IPs available on this computer: Any IP on your PRTG core server system accepts incoming probe connections.
  • Specify IPs: Specify selected IP addresses that accept incoming connections.

Step 2.2: Allow IPs

In the Allow IPs field, you can enter the IP address of the computer on which you want to install a remote probe. You can also enter the word any. This sets the PRTG core server to accept remote probe connections from any IP address.

i_round_redIf you use any, make sure that you only write the word in lower case. Any other variations are not valid.

Changing other settings is not required. For details about the fields for Access Keys, Deny IPs, and Deny GIDs, see section Core & Probes.

When you are done, click Save to save your settings.

i_round_redIf you change this setting, PRTG needs to restart the PRTG core server to apply your changes. After clicking Save, a dialog box appears that asks you to confirm the restart. Click OK to trigger the restart. During the restart, all users of the PRTG web interface, of PRTG Desktop, or of PRTG Apps for Mobile Network Monitoring are disconnected and reconnected.

i_round_blueTo edit the core–probe connection settings, you can also use the PRTG Administration Tool on your PRTG core server.

Cluster and Remote Probes Outside the LAN

i_round_redIf you run PRTG as a cluster and you want to run remote probes outside your local network, you have to make sure that your cluster nodes and the addresses they use are reachable from the outside. Check your cluster node settings under Cluster before you install a remote probe outside your local network. Enter valid addresses (Domain Name System (DNS) names or IPs) for both cluster nodes to reach each other and for remote probes to individually reach all cluster nodes. Remote probes outside your LAN cannot connect to your cluster nodes if they use local addresses.

If you already have a remote probe installed outside your LAN and the remote probe is disconnected because of this, follow these steps:

  1. Uninstall the remote probe.
  2. Update the cluster node settings with addresses that are reachable from outside your LAN.
  3. Restart your PRTG core servers.
  4. Install the remote probe again. It then obtains the IP address or DNS name entries that it can reach.

i_square_cyanSee also section Failover Cluster Configuration, section Remote Probes in a Cluster.

Step 3: Download the Remote Probe Installer from the PRTG Web Interface

  1. On the computer on which you want to install a remote probe, log in to the PRTG web interface.
  2. From the main menu bar, select Setup | Optional Downloads | Remote Probe Installer.
  3. Click Add Remote Probe to start the installation assistant.
    i_round_blueThe Add Remote Probe button is also available in the device tree.
  4. Wait until the installation is completed. The remote probe then automatically connects to your PRTG core server.
  5. In the appearing dialog window, click Prepare and Download to start the download.
  6. Save the setup program to your local disk.

In the installation approach with the assistant, PRTG guides you through the installation process. If you Download the Remote Probe Installer directly, you have to install the remote probe without the assistant.

i_popIf you connect your remote probe to a PRTG on premises instance, prepare your Probe Connection Settings first.

Add Remote Probe Assistant

Add Remote Probe Assistant

i_round_redThe PRTG version numbers of the PRTG core server service and PRTG probe service must match. PRTG automatically updates remote probes when you install a new version on the PRTG core server. If PRTG advises you to manually update your remote probe, open a web browser on the remote computer and download the remote probe installer as described in this section.

Step 4: Install a New Remote Probe

  1. Execute the setup program that you downloaded.
  2. Confirm the Windows User Account Control dialog with Yes to allow the installation. The usual software installation wizard guides you through the installation process.
  3. Click Install to start the installation process.
Remote Probe Setup Installing

Remote Probe Setup Installing

Wait until the installation is complete. The remote probe then automatically connects to your PRTG core server.

Remote Probe Setup Connecting to the PRTG Core Server

Remote Probe Setup Connecting to the PRTG Core Server

If the remote probe successfully connects to your PRTG core server, you can complete the setup of your new remote probe.

i_round_blueTo allow your new remote probe to connect to a PRTG Hosted Monitor instance, PRTG automatically sets the Allow IPs field in Core & Probes to any. You can also use any for PRTG on premises, but we recommend that you use this setting in intranets only. If any is not an option for you, cancel it in the Allow IPs field and enter the IP address of your remote probe instead.

Remote Probe Setup Successful

Remote Probe Setup Successful

  1. Click Continue to finish the remote probe installation.
  1. Click Finish to exit the installation wizard.

The remote probe is now installed on your computer as a Windows service.

Step 5: Approve the New Remote Probe

In the installation assistant, click Installation Done.

Confirm that Installation is Done

Confirm that Installation is Done

i_podIf you successfully installed the remote probe from a PRTG Hosted Monitor installation, you see the following dialog box.

Approve Remote Probe for PRTG Hosted Monitor

Approve Remote Probe for PRTG Hosted Monitor

Click Approve and auto-discover to include the new remote probe and network in your device tree and to start the auto-discovery. It discovers devices and automatically creates suitable sensors. Optionally, click Approve to only approve the remote probe without the auto-discovery. The remote probe appears in your device tree.

For unwanted remote probe connections, click Cancel. A new window appears in the lower-right corner.

Deny Remote Probe

Deny Remote Probe

Click Deny to deny the new remote probe.

i_round_redIf you deny or remove a remote probe, PRTG automatically adds this device's global ID (GID) to the Deny GIDs list in Core & Probes. PRTG automatically denies future remote probe connections from this device.

i_round_blueIf you deny the remote probe in the device tree, it does not uninstall the remote probe, but only denies access to the PRTG core server. The remote probe continues to run on the target system until you uninstall it manually.

Once approved, PRTG automatically opens the new remote probe in the device tree and creates a set of sensors for the remote probe to ensure you can immediately detect bottlenecks on the remote probe system. We recommend that you keep these sensors. You can now create groups, devices, and sensors for monitoring via the new remote probe.

i_round_blueYou do not have to approve remote probes after updates.

When a new remote probe connects to the PRTG core server for the first time, you receive a new ToDo ticket.

Debugging Remote Probe Connection Issues

If you have issues with the connection between the PRTG core server and remote probe, make sure that you meet the following requirements:

  • Recheck if you fulfilled all the requirements as described in step 1 of this section like the Windows Firewall settings.
  • The IP address of the computer on which you want to install a remote probe is not listed in the Deny IPs field in Core & Probes.
  • You can also take a look at the remote probe's logfiles. The probe process writes logfiles with a file name in the format PRTG Probe Log (x).log. Open the one with the most recent date.

For a correct connection, the log should look similar to this:

11/6/2017 1:21:58 PM PRTG Probe V17.4.36.3253
11/6/2017 1:21:58 PM System time zone: (UTC+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna
11/6/2017 1:21:58 PM libeay32.dll=1.0.2.11
11/6/2017 1:21:58 PM ssleay32.dll=1.0.2.11
11/6/2017 1:21:58 PM PRTG Probe "example-DNS" starting on "example-DNS" (GID={AAAA1111-22BB-33CC-DD44-EEEEEE555555})
11/6/2017 1:21:58 PM Memory Manager: NexusMM4
11/6/2017 1:21:58 PM OS: Microsoft Windows 10 Enterprise (10.0 Build 15063), 4 CPUs (Quad x64 Model 78 Step 3), code page "Windows-1252", on "NVME SAMSUNG MZFLV256"
11/6/2017 1:21:58 PM Data Path: C:\ProgramData\Paessler\PRTG Network Monitor\
11/6/2017 1:21:58 PM System Path: C:\Program Files (x86)\PRTG Network Monitor\
11/6/2017 1:21:58 PM Local IP: 0.0.0.0
11/6/2017 1:21:58 PM Core Server IP: example-DNS.exampledomain.com
11/6/2017 1:21:58 PM Core Server Port: 23560
11/6/2017 1:21:58 PM SSL Enabled
11/6/2017 1:21:58 PM Probe GID: {AAAA1111-22BB-33CC-DD44-EEEEEE555555}
[...]
11/6/2017 1:21:58 PM Start Connection
11/6/2017 1:21:58 PM Start Done
11/6/2017 1:21:58 PM (14608):Initializing WMIConnectionPool
11/6/2017 1:21:58 PM (14608):WMIConnectionPool maximum number of concurrrent establishings is set to: 20
11/6/2017 1:22:03 PM Connect from to example-DNS.exampledomain.com:23560
11/6/2017 1:22:03 PM TCP connected from 10.49.12.51:55199 to example-DNS.exampledomain.com:23560
11/6/2017 1:22:03 PM State changed to connected (example-DNS.exampledomain.com:23560)
11/6/2017 1:22:03 PM Reconnect
11/6/2017 1:22:04 PM Connected
11/6/2017 1:22:10 PM Send Login
11/6/2017 1:22:10 PM Local: 11/6/2017 1:22:10 PM UTC: 11/6/2017 12:22:10 PM
11/6/2017 1:22:10 PM MarkUnused
11/6/2017 1:22:10 PM Login OK: Welcome to PRTG

If the connection fails, for example because of an incorrect Access Key, or because of incorrect IP settings (see step 2), you see:

11/6/2017 1:42:02 PM Try to connect...
11/6/2017 1:42:02 PM Connected to 10.0.2.167:23560
11/6/2017 1:42:07 PM Login NOT OK: Access key not correct!

If you need to adjust any settings for the connection to the PRTG core server, use the PRTG Administration Tool on the remote probe system.

Remote Probe Settings in PRTG Administration Tool

Remote Probe Settings in PRTG Administration Tool

Under Connection to PRTG Core Server, you can then edit the following settings:

  • Server: Enter the IP address or Domain Name System (DNS) name of the PRTG core server that the remote probe is to connect to. If you use network address translation (NAT) rules, you must enter the IP address that is externally visible, because the remote probe connects from outside your network.
  • Probe Access Key and Confirm Access Key: Enter the access key that the remote probe is to send to the PRTG core server. You have to define this access key on the PRTG core server in Core & Probes. Make sure that the access keys match.

Click Save & Close to confirm your settings and to (re)start the PRTG probe service.

i_square_cyanFor more information about these settings, see section PRTG Administration Tool.

More

i_square_blueKNOWLEDGE BASE

I cannot open the PRTG web interface via the desktop shortcut anymore. What can I do?

How can I customize ports for core-probe connections used by PRTG?

 

i_square_bluePAESSLER WEBSITE

How to connect PRTG through a firewall in 4 steps

How to install a PRTG remote probe in 4 steps

Installing the Software